{"product_id":"cr-99076","title":"SKF CR99076 Hardened Stainless Speedi Sleeve for Shafts 19-19.1mm","description":"\u003cp\u003e\u003cstrong\u003eSKF Speedi Sleeve: \u003c\/strong\u003eThe quickest and most sensible way to repair a worn shaft. The  Speedi sleeve range offers the opportunity to repair \u003cstrong\u003eseal\u003c\/strong\u003e counter faces on shafts without prior dismantling or machining of the equipment and once fitted offers superior surface and sealing characteristics often outperforming the original life span of the shaft. Speedi Sleeves are designed to repair shafts where oil seals run. The sleeve is sufficiently thin-walled (.011\" or 0.28 mm) to allow the \u003cstrong\u003esame size of seal\u003c\/strong\u003e to be used. The Speedi-Sleeve® is made of high quality stainless steel SAE 304. The surface is wear-resistant and machined without directionality to a finish of Ra = 10 to 20 micro inches or 0.25 to 0.5 µm.\u003cbr\u003e\r\n\u003cstrong\u003eBenefits: \u003c\/strong\u003eNo dismantling of equipment, longer life cycle, cost effective.\u003cbr\u003e\r\n\u003cstrong\u003eNote:\u003c\/strong\u003e Speedi sleeves are only suitable for repairs where an oil seals needs to run, they cannot be used  to repair damage where a bearing fits onto a shaft. \u003c\/p\u003e\r\n\u003cp\u003e\u003cbr\u003e\r\n\u003cstrong\u003eInstallation Instructions:\u003c\/strong\u003e\u003cbr\u003e\r\n\u003cstrong\u003e1.\u003c\/strong\u003e Wipe the surface where the seal contacts the shaft. File down and polish any burrs or rough spots.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e2.\u003c\/strong\u003e Measure the diameter on an unworn portion of the shaft where the sleeve will be positioned. Measure in three positions\r\nand average the measurements in case the shaft is out of round. If the average diameter is within the range for a given\r\nsleeve size, there is sufficient press-fit built into the sleeve to keep it from sliding or spinning. No adhesive is required.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e3.\u003c\/strong\u003e If the shaft is deeply scored, fill the groove with a powdered metal epoxy type filler. Install the sleeve before the filler hardens.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e4.\u003c\/strong\u003e If the groove does not require filling, apply a light layer of a non-hardening sealant to the inside diameter surface of the sleeve.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e5.\u003c\/strong\u003e Determine how far back the sleeve must be positioned to cover the old seal wear tracks. The sleeve must be placed over the worn area, not just bottomed or left flush with the end of the shaft.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e6.\u003c\/strong\u003e If the flange should be removed after installation, cut it from the outside diameter into the radius in one location. The flange end of the sleeve goes on the shaft first. Place installation tool over the sleeve.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e7.\u003c\/strong\u003e Gently tap the centre of the tool until the sleeve covers the worn surface. If the installation tool supplied with the sleeve is too short, a length of pipe or tubing with a squared-off, burr-free end can be used. Be sure that the inside diameter of the pipe is the same as that of the installation tool.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e8.\u003c\/strong\u003e Make sure that the sleeve is installed so that its outside edge is seated on the full shaft diameter, not resting in the chamfer area.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e9.\u003c\/strong\u003e If the flange was cut for removal, use a pair of long-nosed pliers to grasp the flange away from the installed sleeve and twist it into a coil. The flange will break loose along the tear-off groove.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e10.\u003c\/strong\u003e After the sleeve is installed, check again for burrs that could damage the seal.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e11.\u003c\/strong\u003e Lubricate the end of the sleeve before installing the seal.\r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cstrong\u003e12.\u003c\/strong\u003e Proceed with seal installation. \r\n\u003cbr\u003e\u003cbr\u003e\r\n\u003cfont color=\"red\"\u003e\u003cstrong\u003eImportant note: Never use heat to install SKF Speedi Sleeve\u003c\/strong\u003e\u003c\/font\u003e\u003c\/p\u003e","brand":"SKF","offers":[{"title":"Default Title","offer_id":52216724324693,"sku":"CR.99076","price":47.37,"currency_code":"EUR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0979\/1491\/3109\/files\/skslv_0ca2417d-ddc5-4198-a107-91ca0c7bcae9.jpg?v=1774368894","url":"https:\/\/simplybearings.nl\/products\/cr-99076","provider":"Simply Bearings Ltd - Ball Bearings, Oil Seals, O-rings, V-Belts, SKF","version":"1.0","type":"link"}